Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Grumpy

Pages: [1]
1
I have a very nice Custom 18650 Titanium light for trade.

It can accept Max. 4.2V, size to fit unprotected 18650 li-ion or small size protected li-ion.

( 5 modes: High -> Medium -> Low -> Strobe Mode -> SOS Mode) (Last mode memory)

+ P4 W0 tint (Support Li-ion x1 only) (Reverse battery protection)




By grumpyatcpf at 2008-09-24


By grumpyatcpf at 2008-09-24

There were only 10 of these made.

Send me PM or post here if you have something you would like to trade.




2
Garage Sale / Kershaw Talon Titanium Knife ATS-34 $75
« on: March 12, 2008, 08:01:14 AM »
This knife is in very good shape.
It has only been very slightly sharpened. Must look close to tell.
These have been discontinued for some time.
I think this is one of the first knives that Kershaw made in Titanium.

4" closed
3" ATS-34 blade
Titanium Handle
Removeable pocket clip for tip up carry.
Lanyard Hole
Thumbstud
Linerlock

It is very easily opened and closed with one hand.





3
Lights Buy/Sell/Trade / Peak Baltic Stainless Extra Long Runtime
« on: February 27, 2008, 05:40:49 AM »
If there is anyone here that would like to have this light that can't afford it just post "I'd like this light" and it is yours. I hope that it is someone that will use it alot maybe for EDC. You must have been a member here before I posted this however.

It is the Extra Long Runtime version.

See details of the light here http://www.peakledsolutions.net/Products/Baltic_SS.html


I was very lucky and won a Dragonheart flashlight.


4
Garage Sale / Boker Lambda Cera Titan
« on: February 11, 2008, 05:27:23 AM »
From the boker website
http://www.boker.de/us/index.php?c=20,1,16


"The world's finest folding knives featuring the newly developed blade material: sintered titanium. Past attempts to produce a titanium blade have missed the mark since titanium alone cannot be hardened like steel, failing to produce any kind of sustained cutting capacity. However, our Cera-Titan blade consists of sintered titanium powder, which includes extremely hard elements mixed in with a bit of silver particles. This revolutionary process offers the benefits that traditional steel cannot. The Cera-Titan blade is 40% lighter than steel, will stay sharp much longer than a high-grade stainless steel blade, will not rust, and is flexible. One more plus, when sharpening is needed, the blade can be honed on a conventional sharpening system (finish with a ceramic rod for best results). Although the overall hardness of this blade is rather low, the cutting power and edge retention still surpasses that of any of the high caliber blade steels currently in use."


Has anyone been curious how this blade material would perform but don't want to buy an expensive knife to find out?

Here's your chance to get one slightly used for free.

The first person to
1)Name the other six
2) followed by I'll take it
gets it.


5
Mr. Bulk / Modifying Lioncub and Chameleon with Seoul led.
« on: March 21, 2007, 12:06:15 AM »
I am thinking of doing this modification for a small fee. See this thread. http://flashlight-forums.com/index.php/topic,4471.msg76857.html#msg76857

If anyone else is offering this specific mod. already please let me know.

I want to use this thread to do some research on this mod. before I actually do any.

Also please post here if you are interested in getting this mod done.

The main questions I have are about the Chameleon and Lioncub drivers.

Can you use the Lioncub driver without sorting the VF of the leds?  If so approx. how many ma is this driver off a freshly charged Rcr123 battery?

Is their anywhere that I can purchase the Seoul leds from that have already been sorted for VF? (For a premium)
What VF does the led need to be to be able to run at least on the 1000ma table of the Chameleon driver safely?

Also is there a reflector that can be used in the Lioncub  that is made Specifically for the Seuol led that would not require any modification or less modification.

Is there a better reflector for use in the Chameleon with the Seoul led?

Did the lioncubs have the same reflector as the Chameleon with slimhead?
If not are they also good reflectors for use with the Seoul led with a little modification?

If I will be able to do this mod or not is dependent on the answers to the above questions. I will only do this if I can do it correctly.

Should I use stars or (bare emitters with my copper spacer). It would be much easier to use stars that have electrical isolation.










6
Lights Buy/Sell/Trade / Lion cub with U bin Seoul P4 $160
« on: March 16, 2007, 11:11:28 PM »


I had originally purchased a slim head and slim tail for my Chameleon flashlight. I gave my Chameleon flashlight away to a friend after modifying it with a Seoul U bin emitter. I purchased a extra control module and used the slim head, slim tail, a lioncub driver, and Seoul U bin P4 led to make this light. The light has a nice bright and white beam. It also has a nice beam pattern to it.
I also polished the aluminum to make this light look much better and installed a gray switch boot.

I had a machinist where I work make me a copper spacer which if I remember correctly was .105 thick and approx. .605 in diameter. (The thickness of the stock star plus .030 for the different focal length of the new emitter). I then removed approx. .030 from the back of the stock reflector which gave it a nice beam. The led was applied under pressure with Artic Alumina to the copper spacer, then the spacer was epoxied to the flashlight body with Artic Alumina under little pressure so not to make electrical contact with body. This gets the heat from the emitter to the copper spacer quickly since it was applied under pressure and there is a larger surface area to get the heat to the body of the flashlight where I had to leave the Artic thicker to isolate from the body. I painted the wires where they are soldered to the emitter with fingernail polish and made a washer out of a thin piece of plastic and placed between the emitter and the reflector to keep the reflector from touching the leads.

I will offer a 1 year labor warranty on this light. (The purchaser of this light would buy the parts). I have modified several lights with better leds and have not had any problems with any so far. If a better Led comes to the market I would also be willing to install it for you if it did not require much modification to the light.

Selling to fund the purchase of another flashlight.

Asking $160 shipped.



I accept paypal, MO, or personal check (will wait to clear).
First to post I'll take it gets it.

7
Lights Buy/Sell/Trade / Surefire 10x SOLD
« on: February 09, 2007, 12:11:00 PM »
This light is in like new condition except for small marks on rubber grip. It includes the charger and works perfectly. Asking $325. Will sell for less depending on type of payment used. Or make me an offer. Also would consider trades.

Please go to the following link for more information on this light.
http://www.surefire.com/maxexp/main...r/908/sesent/00


8
$300 plus shipping. This light retails for $400 not including the handlebar mount which is $35 extra
I require shipping with insurance. I package my items very well and will ship very fast. Please send PM for payment info.

I accept MO, paypal, and personal check (will wait for it to clear).
First to post "I'll take it" or similar gets it.
This light is like new and comes with charger, battery, helmet mount, handlebar mount, instructions. Does not include the box.

Here is the link to the Jet website for picture and description of light. http://www.jetlites.com/hid_helmet.html



This light has both the handlebar and the helmet mount.
The following is from their website.
The Jet Lites Blast HID Helmet Bike Light features JET's 13W HID Blast, which is 2x more efficient than JET's 20w halogen light. This energy efficient light makes it a perfect product for those riders needing maximum brightness with long burn times. The Jet Lights Blast HID helmet bike light is ideal for all riding conditions. From city streets to high speed technical rocky descents, it can go anywhere and deliver the visual comfort of daylight like conditions. The canister battery fits cleanly in any water hydration pack. JET's exclusive thread lock cable system delivers vibration, shock, short, and waterproof reliability. The Jet Lites Blast HID Helmet Bike Light features an easy to use aim-as-you-ride helmet mount, with JET's patented safety breakaway system. This elegantly designed two piece mount will break apart with a 5lb impact. It can be reassembled in seconds. This feature could be the difference between a neck injury and no injury at all in the event of a fall or the light catching a low hanging branch. A must have feature.

FEATURES:

    * JET Blast HID 13w flood light head
    * aim-as-you-ride helmet mount with safety breakaway
    * 5 hr fast charger

SPECS:

    * Light Head:
          o 13W HID Lamp and balast 130g (4.6 oz.)
    * Battery:
          o 13.2v 3800 NiMH battery pack
          o 675 grams (23.8 oz.)
          o Battery cycle life: 400 charges or 3 5 years or any combination of the two events
    * Charger:
          o Intelligent 5 hr fast charger
    * Run Time:
          o 3 hours, 45 minutes
    * Weight:
          o Complete System: 31 oz. (875 grams)
    * Warranty (USA only):
          o 1 year on system, 30 days on lamp and balast

9
Lights Buy/Sell/Trade / Sold Pending Dam Cham #20 for sale.
« on: September 12, 2006, 03:37:22 AM »
Please see the following link. http://flashlight-forums.com/index.php?topic=2280.msg41513#msg41513
Scroll down a little for a picture of this light. Once you click on the link it has a picture of this particular light singled out because of its unique colors from the heat treatment process.

Asking $900 which includes priority shipping with insurance.

This is a direct link to the picture I was referring to above.
http://darkgear.com/mrbulk/cpf/DCView.jpg

I will accept Paypal, MO or personal check. Payment must be paid within 24 hours or if paying with MO or personal check you must PM me and let me know when you will be mailing payment. Mail MO or personal check with tracking number so I will know when to expect it to arrive. I will wait on MO or personal check to clear before mailing.

First to post I'll take it and pay shortly after gets it.

Please note that this light will also be listed at CPF so I will go by timestamp.



10
Lights Buy/Sell/Trade / WTB Lioncub V2 Driver
« on: March 30, 2006, 04:47:34 PM »
If someone has a V2 driver from a lioncub that they have replaced with the new regulated driver let me know what you want for it.

11
Lights Buy/Sell/Trade / Make me an offer for my Ti Chameleon
« on: February 09, 2006, 07:36:35 AM »
I am thinking of selling my Ti Chameleon.
I will make my decision on wheather I will sell it or not based on what I am offered.
It is mint and has never been ran above 500ma and not very long at that.

Please send me offer via PM.




Pages: [1]